E Ride Pro SS Parts & Maintenance Guide — All Models (SS 1.0, 2.0, 3.0, SR)

Maintenance guide for the E Ride Pro SS series — drive belt replacement, brake fluid differences between Type 1 and Type 2, tire fitment by model, and OEM part numbers.

7 min read

The E Ride Pro SS lineup — SS 1.0, SS 2.0, SS 3.0, SR, and the Pro S variants — spans several years of hardware revisions. The key maintenance trap: two different brake fluid specs and two different drive belt widths exist across the model range, and using the wrong one causes real damage. This guide covers what you need to know for each model.

1. Drive Belt — Two Specs, Not Interchangeable

All E Ride Pro SS models use a belt drive — no chain, no chain lube. Belt maintenance is minimal under normal conditions, but when replacement is due, getting the right belt matters.

Type 1 Models: SS 1.0, SS 2.0, Pro S, Mini, Mini R

OEM E7006 Drive Belt — $80.99

This is the standard E Ride Pro belt that fits the majority of the lineup. It is a specific OEM part — do not substitute a generic belt without confirming the tooth profile and width match exactly.

Type 2 Models: SS 3.0 and SR

OEM SS 3.0 Drive Belt (20mm) — $85.99

The SS 3.0 and SR use a wider 20mm belt. It is not interchangeable with the E7006. If you install the narrower belt, it will skip under high torque loads.

Belt service tips:

  • Inspect monthly — look for cracks, fraying, or glazing on the contact surface
  • Clean with a dry rag only — no solvents, no lubricants on the belt
  • Replace the rear pulley when installing a new belt — worn pulley teeth accelerate new belt wear
  • Torque the rear axle nut to spec after belt replacement — undertightening causes belt skip

2. Brake System — Fluid Spec Differs by Generation

This is the most critical maintenance distinction on the E Ride Pro platform:

  • Type 1 (SS 1.0, SS 2.0, Pro S, Mini, Mini R): DOT 3 brake fluid — $8.99
  • Type 2 (SS 3.0, SR): DOT 4 brake fluid — $8.99

DOT 3 and DOT 4 are technically compatible (both glycol-based), but using DOT 3 in a DOT 4 system means a lower boiling point — which matters under aggressive braking. More importantly, do not use mineral oil in any E Ride Pro model — the seals are DOT-compatible, not mineral oil-compatible.

Brake pads (all Type 1 models): Front kit $23.99 / Rear $23.99.

Brake lever set: $23.99.

3. Tires by Model

SS 3.0 and SR (19"/18")

Mini and Mini R (14"/12")

4. Cockpit

Maintenance Schedule

  • Before every ride: Belt visual, tire pressure, brake lever feel
  • Monthly: Belt inspection for cracking or glazing, pulley check
  • Every 20 hours: Brake pad thickness, spoke tension, wheel bearing check
  • Annually: Brake fluid flush (DOT 3 or DOT 4 per your model), belt replacement if needed

Browse the full E Ride Pro SS parts catalog on Wired Whips — OEM parts for all SS models with verified fitment by model year.

Frequently Asked Questions

What drive belt does the E Ride Pro SS use?

It depends on the model. The SS 1.0, SS 2.0, Pro S, Mini, and Mini R use the OEM E7006 belt ($80.99). The SS 3.0 and SR use a wider 20mm belt ($85.99). The two belts are NOT interchangeable — using the wrong belt will slip and fail. Confirm your exact model before ordering.

What brake fluid does the E Ride Pro SS use?

It depends on the model — this is the most common parts mistake on the E Ride Pro platform. Type 1 models (SS 1.0, SS 2.0, Pro S, Mini, Mini R) use DOT 3 brake fluid ($8.99). Type 2 models (SS 3.0 and SR) use DOT 4 brake fluid ($8.99). Using the wrong fluid can cause seal degradation and brake failure. Confirm your model type before topping up or bleeding.

What tire sizes does the E Ride Pro SS 3.0 use?

The E Ride Pro SS 3.0 and SR use a 19-inch front and 18-inch rear. OEM tires are 70/100-19 front ($102.99) and 80/100-18 rear ($102.99). These are standard MX sizes — Bridgestone, Dunlop, and IRC all produce compatible tires in these sizes.

What tire sizes does the E Ride Pro SS 2.0 use?

The E Ride Pro SS 2.0 uses a 19-inch front and 18-inch rear — the same sizing as the SS 3.0, but the OEM tires are different compounds and may be different dimensions. Use OEM replacement tires from E Ride Pro or verified aftermarket options in 70/100-19 front and 90/100-18 rear.

How often should I replace the drive belt on the E Ride Pro SS?

Under normal riding conditions, the E Ride Pro drive belt should last 300–500 hours before replacement is needed. Inspect monthly for cracking, fraying, or glazing. A glazed belt will slip under hard acceleration — replace it immediately. Keep the belt and pulleys clean; oil or dirt contamination dramatically reduces belt life.

← All GuidesBrowse All Parts →